DIY Necklace Organizer (Please Help Me Finish Or Improve Upon This Design!)

Yesterday, I labored on constructing the ultimate piece of the perimeter cupboards in my walk-in closet — a DIY necklace organizer. For the final 12 months, I’ve been utilizing this quite simple DIY jewellery organizer that I made to take a seat on the countertop in our lavatory.

So with that in thoughts, here’s what I got here up with. I constructed a drawer-type construction that doesn’t have a backside on it, put it on drawer slides, and added two closet rods contained in the construction. When it’s pushed into the cupboard, it appears like this…

After which it pulls out like a drawer so I can simply entry the necklaces…

The constructing course of was extremely easy. I ripped some 1/2-inch plywood (the identical plywood I used to construct my jewellery drawer) to 6 inches large, after which I reduce a protracted piece for the again, and two quick items for the edges. I nailed these collectively utilizing 1.5-inch 18-gauge nails.

After which, to maintain these items sq., I ripped one other strip of 1/2-inch plywood to 2.5 inches large, reduce it to the correct size on my miter noticed, and nailed that to the highest on the again in order that it was nailed into the highest edges of the edges items and the again piece.

After which I added the drawer slides, slid the construction into the cupboard, and added the closet rods. I used the identical closet rods that I’ll be utilizing for the hanging storage within the closet. Yow will discover these right here (affiliate hyperlink).

And naturally, I’ll be portray the entire thing the identical colour as the cupboards, so it’ll mix in as soon as it’s painted.

I used to be anxious to see how it might look with all of my necklaces hanging on it, so I went forward and added these. I staggered the peak of the 2 bars, with the again bar about two inches larger than the entrance bar. And I do wish to determine a approach so as to add tape lights below there. I feel it is going to look wonderful to have these lit from the again.

And right here’s what it appears like after they’re pulled out for simple entry.

General, I actually love the simplicity of the design. And it pulls out simply simply by grabbing the bar and pulling. So there’s no want to determine a approach so as to add any further pulls.

I do know many individuals advised that I discover a method to carry the necklaces as much as eye degree, however actually, I’m so quick that this can work out completely for me. I deliberately put in the glass countertop a bit larger than countertop peak in order that the necklaces may very well be up a few inches larger than I had initially deliberate.

My peak, plus the truth that it pulls out for simple entry, makes this design work out completely for me.

The one factor I’m not sure about is the right way to end off these edges. Clearly, I can’t depart it like this with the sting of the plywood and the drawer slide displaying.

I’ve had two concepts for ending off these edges. The primary is to repeat the design that I used on the prime of the cupboards…

There are a few points with that, however possibly I might determine them out. First, these corbels on the prime are 4.5 inches sq.. The body for the necklace organizer is six inches excessive. So if I attempt to repeat that design, the underside tail on it must be longer. I’m undecided if that may throw off the continuity of the design, or if it might work. Additionally, there’s nothing to nail that prime edge to, so it might simply be free. I’m undecided if it might keep put. The one factor I’ve to nail it to is the six-inch-high fringe of the 1/2-inch plywood. Right here’s a mock-up I did of that potential design.

The only method to end it off could be to make use of a slender piece of wooden hooked up to the sting of that plywood. I examined out this concept utilizing a 1″x2″ (which is definitely 1.5″ large), but when I am going this route, I’d rip that right down to only one″ large, which is all that I have to cowl the sting of the plywood. I used my band noticed to spherical off the underside nook of the piece to see what that may seem like.

So these are the 2 concepts I had, however I do know that y’all are extremely inventive and should have a greater concept. If something involves thoughts, let me know! I wish to hold it easy, and I don’t need something to cowl the entrance of the necklaces.

If I can determine that remaining piece, I’ll formally have each single a part of the perimeter cupboards constructed. This necklace storage was the very last thing I had to determine and construct, and people ending touches on the necklace storage are the ultimate items of the puzzle.